0

DM-4-2-T-KNX

DM-4-2-T-KNX

DM-4-2-T-KNX

DM 4-2 T KNX

4-way universal dimmer actuator FIX1
For dimming dimmable LED, incandescent lamps, LV, HV halogen lamps and energy saving lamps
Also suitable for dimming of dimmable energy-saving lamps
Also suitable for controlling fans
LED switching status display for each channel
Manual operation on device
Dimming output: 200 W per channel
Automatic load detection (can be deactivated)
For R, L and C loads

SKU: 4940200-1 Categories: Actuators DIN rail and gateways, KNX Brand: theben

Description

Description

Technical data

Operating voltage KNX	Bus voltage, ≤10 mA
Operating voltage	230 V AC – 240 V AC, 50 Hz – 60 Hz
Frequency	50 – 60 Hz
Stand-by consumption	<1 W
Width	4 modules
Installation type	DIN rail
Type of connection	Terminal screws \| Bus connection: KNX bus terminal
Max. cable cross section	Solid wire: 0.5 mm² (Ø 0.8) to 6 mm² \| Stranded wire with end sleeve: 0.5 mm² to 4 mm²
Number of channels	4
Lamp types	Incandescent, low-voltage and high-voltage halogen and dimmable energy saving lamps and LED
Incandescent/halogen lamp load	200 W
Energy saving lamps	Trailing edge (RC-mode): 200 W
Switching capacity min.	2 W
Max. cable length	100 m
Ambient temperature	-5°C … 45°C
Type of protection	IP 20
Protection class	II according to EN 60 669

Downloads

Hand book	PDF	200 W KNX-Dimmer (1,3 MB)
Operating instructions	PDF	4940280 (1,9 MB)
KNX-Database (Single Product)	ZIP	200 W KNX-Dimmer (951,6 kB)
CAD symbol	ZIP	4940280 (1,6 MB)
Data sheet	PDF	DM 4-2 T KNX (465,2 kB)
Brochure	PDF	KNX home and building control brochure (5,9 MB)
Catalogue	PDF	General catalogue 2022 (35,1 MB)

RECENT VIEWER

RM 16 T KNX

RM 16 T KNX

RM 16 T KNX

16-way switching or 8-way blind actuator FIX2
Flexible channel function selection as switching actuator or for controlling drives for blinds,shutters, sun and vision protection devices, skylights and ventilation flaps
LED switching status display for each channel
Manual operation on device (even without bus connection)

SMG 2 S KNX

SMG 2 S KNX

SMG 2 S KNX

2-way 1-10 V control unit MIX
Base module MIX
Can be upgraded to maximum of 6 channels
Free combination of switches, dimming, blinds and heating control as well as binary inputs
Switching and dimming of lighting circuits in combination with electronic ballasts (EBs and ballasts LED)
1-10V inputs and one switch output (relay contact) per channel
LED switching status display for each channel
Manual switch with On/Off/Bus settings (also without bus voltage)
With crossover switching to spare the relay contact

iON 102 KNX BK

iON 102 KNX BK

iON 102 KNX BK

Push-button sensor with 2 buttons and 2 status LEDs with integrated temperature sensor
Secure communication with support of „KNX Data Secure“
For controling of the functions switching, dimming, blinds, value transmitter, operating mode, scene, color control, sequence
Up to 3 different telegrams per button
Sending different telegrams with a short, long or double click
Multi-colored status LEDs with adjustable colors for each LED separately
Behavior of each status LED can be set: static, flashing or pulsing
Brightness of each status LED can be individually adjusted via object or parameter
Automatic brightness control of the status LEDs depending on the ambient brightness
Integrated temperature sensor for visualization and temperature control via heating actuators

Function monitoring via object (signaling dismantling)
Installation of two iON push button sensors on standard double socket with accessory possible
Transparent cover for individual labeling in the scope of delivery

RME 8 S KNX

RME 8 S KNX

RME 8 S KNX

8-way switching actuator MIX2
Extension module MIX2
For upgrading to maximum of 24 channels
Up to two extension modules MIX or MIX2 can be connected to one base module
Device and KNX bus module can be swapped independently of each other
Removable KNX bus module enables devices to be changed without reprogramming
Manual set-up and use of switching actuators is possible without KNX bus module
LED switching status display for each channel
Manual operation on device (even without bus connection)
Adjustable characteristics: e.g. switching, delayed switching, pulse function

Links, type of contact (NC contact/NO contact) and participation in central commands such as continuous On, continuous Off, central switching and save/call up scene
Switching functions: On/Off, pulse, On/Off delay, staircase light with warning
Logical links: e.g. lock, AND, release, OR

Chopin - brushed nickel

Chopin – brushed nickel

Chopin, meet the maestro. Controlling Chopin feels a bit like playing the piano. Push the levers up or down to intuitively dim the lights, close the curtains, and let your favorite music enter the room. Press and hold the levers for even more functions. An internal temperature sensor discretely reports the room temperature. The integrated thermostat function does the rest. Combine Chopin with our sockets in a horizontal or vertical 2-gang configuration. Opt for 1 or 2 levers in 3 different finishes: black aluminum, chromed, or gold plated, creating a sophisticated and timeless appearance.

Core Plus

Core Plus

Core Plus is our all-in Basalte server. Fast, packed with functionality and using our latest and greatest platform. Core Plus is the most complete Core server we have ever built! Lighting, climate, music and security are only a tap away.

HMG 6 T KNX

HMG 6 T KNX

HMG 6 T KNX

6-way heating actuator MIX2
With 6 temperature controllers (P/PI) for heating and cooling
Base module MIX2
Can be upgraded to maximum of 18 channels
For controlling thermal actuators 24 V - 240 V AC in 2 groups with 3 outputs and 450 mA each
(Due to the switch-on behaviour of the actuators, we recommend not to exceed a maximum load of 3x1 actuators 24 V AC or 3x5 actuators 230 V AC)
Short-circuit-proof and overcharge protected
Continuous or switching actuating value selectable
Valve protection function can be deactivated
With the modes: comfort, standby, night as well as frost/heating protection

Changeover to summer mode possible
Up to two extension modules MIX or MIX2 can be connected to one base module
Device and KNX bus module can be swapped independently of each other
Removable KNX bus module enables devices to be changed without reprogramming
Manual set-up and use of actuator is possible without KNX bus module
LED switching status display for each channel
Manual operation on device (even without bus connection)

RMG 4 I KNX

RMG 4 I KNX

RMG 4 I KNX

- 4-way C load switching actuator MIX2
- With current recognition
- For higher lamp loads
- Base module MIX2
- Can be upgraded to maximum of 12 channels
- Up to two extension modules MIX or MIX2 can be connected to one base module
- Device and KNX bus module can be swapped independently of each other
- Removable KNX bus module enables devices to be changed without reprogramming
- Manual set-up and use of switching actuators is possible without KNX bus module
- LED switching status display for each channel
- Manual operation on device (even without bus connection)
- Adjustable characteristics: e.g. switching, delayed switching, pulse function
- Links, type of contact (NC contact/NO contact) and participation in central commands such as continuous On, continuous Off, central switching and save/call up scene
- Switching functions: On/Off, pulse, On/Off delay, staircase light with warning
- Logical links: e.g. lock, AND, release, OR

iON 104 KNX SR

iON 104 KNX SR

iON 104 KNX SR

Push-button sensor with 4 buttons and 4 status LEDs with integrated temperature sensor
Secure communication with support of „KNX Data Secure“
For controling of the functions switching, dimming, blinds, value transmitter, operating mode, scene, color control, sequence
Up to 3 different telegrams per button
Sending different telegrams with a short, long or double click
Multi-colored status LEDs with adjustable colors for each LED separately
Behavior of each status LED can be set: static, flashing or pulsing
Brightness of each status LED can be individually adjusted via object or parameter
Automatic brightness control of the status LEDs depending on the ambient brightness
Integrated temperature sensor for visualization and temperature control via heating actuators

Function monitoring via object (signaling dismantling)
Installation of two iON push button sensors on standard double socket with accessory possible
Transparent cover for individual labeling in the scope of delivery

RME-4-I-KNX

RME-4-I-KNX

RME 4 I KNX

4-way C load switching actuator MIX2
With current recognition
For higher lamp loads
Extension module MIX2
For upgrading to maximum of 12 channels
Up to two extension modules MIX or MIX2 can be connected to one base module
Device and KNX bus module can be swapped independently of each other
Removable KNX bus module enables devices to be changed without reprogramming
Manual set-up and use of switching actuators is possible without KNX bus module
LED switching status display for each channel

Manual operation on device (even without bus connection)
Adjustable characteristics: e.g. switching, delayed switching, pulse function
Links, type of contact (NC contact/NO contact) and participation in central commands such as continuous On, continuous Off, central switching and save/call up scene
Switching functions: On/Off, pulse, On/Off delay, staircase light with warning
Logical links: e.g. lock, AND, release, OR

HME 6 T KNX

HME 6 T KNX

HME 6 T KNX

6-way heating actuator MIX2
With 6 temperature controllers (P/PI) for heating and cooling
Extension module MIX2
For upgrading to maximum of 18 channels
For controlling thermal actuators 24 V - 240 V AC in 2 groups with 3 outputs and 450 mA each
(Due to the switch-on behaviour of the actuators, we recommend not to exceed a maximum load of 3x1 actuators 24 V AC or 3x5 actuators 230 V AC)
Short-circuit-proof and overcharge protected
Continuous or switching actuating value selectable
Valve protection function can be deactivated
With the modes: comfort, standby, night as well as frost/heating protection

Changeover to summer mode possible
Up to two extension modules MIX or MIX2 can be connected to one base module
Device and KNX bus module can be swapped independently of each other
Removable KNX bus module enables devices to be changed without reprogramming
Manual set-up and use of actuator is possible without KNX bus module
LED switching status display for each channel
Manual operation on device (even without bus connection)

Training case KNX

Training case KNX

Training case KNX

KNX training case with various KNX products for training or practice purposes
Contains 12 KNX products that can be commissioned and parameterized for training purposes
The actions of the products are realistically displayed via lights and LED panels on a building floor plan
Clear structure of all components, easy introduction to the topic of KNX

Username or email address *

Password *

Remember me

Lost password? Recover password

Email address *

Password *

Your personal data will be used to support your experience throughout this website, to manage access to your account, and for other purposes described in our privacy policy.

Shopping Cart

Add Order Note Edit Order Note Save Cancel

Estimate Shipping